Inovance Aonarch MD500L Series Скачать руководство пользователя

Страница: 7 / 69

Safety Instructions

- 6 -

Operation

DANGER

◆

Do not touch any wiring terminals during operation. Failure to comply will result in an electric

shock.

◆

Do not remove any part of the equipment during operation. Failure to comply will result in an

electric shock.

◆

Do not touch the equipment shell, fan, or resistor for temperature detection. Failure to comply

will result in heat injuries.

◆

Signal detection must be performed only by professionals during operation. Failure to comply

will result in personal injuries or equipment damage.

WARNING

◆

Prevent metal or other objects from falling into the device during operation. Failure to comply

may result in equipment damage.

◆

Do not start or stop the equipment using the contactor. Failure to comply may result in

equipment damage.

Maintenance

DANGER

◆

Equipment installation, wiring, maintenance, inspection, or parts replacement must be

performed only by professionals.

◆

Do not maintain the equipment at power-on. Failure to comply will result in an electric shock.

◆

Before maintenance, cut off all equipment power supplies and wait at least 10 minutes.

WARNING

◆

Perform daily and periodic inspection and maintenance for the equipment according to

maintenance requirements and keep a maintenance record.

Repair

DANGER

◆

Equipment installation, wiring, maintenance, inspection, or parts replacement must be

performed only by professionals.

◆

Do not repair the equipment at power-on. Failure to comply will result in an electric shock.

◆

Before inspection and repair, cut off all equipment power supplies and wait at least 10

minutes.

WARNING

◆

Require repair services according to the product warranty agreement.

◆

When the equipment is faulty or damaged, require professionals to perform troubleshooting

and repair by following repair instructions and keep a repair record.

◆

Replace quick-wear parts of the equipment according to the replacement guide.

◆

Do not operate damaged equipment. Failure to comply may result in worse damage.

◆

After the equipment is replaced, perform wiring inspection and parameter settings again.

Содержание Aonarch MD500L Series






































































Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды

Inovance Aonarch MD500L Series, Руководство пользователя

Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды