Inovance Aonarch MD500L Series Скачать руководство пользователя

Страница: 43 / 69

- 42 -

Quick setup

Table 4-2

Parameter setting for activating the UPS/ARD mode rescue operation in

MD500L

Parameter

Parameter Name

Setting Range

New Setting to Enable

F4-06

DI7 function selection

(On-board expansion

card)

15-Multi Speed Reference 4

F4-06=15

FC-08

UPS reference frequency

0.0 to 100.0%

FC-08= ≤ 20% ( ≤ 10HZ) for

Rescue speed in UPS/ARD

Power supply

A5-06

UnderVoltage Throsold

Level

60% to 140%

A5-06=60%

Optional Parameter when inverter software current limit function is used to check the least current

durection running in UPS/ARD mode

F5-05

Extension card relay

function (MC+/MC-)

36 Software current

Exceeding Limit

F5-05=36

F8-36

Output current

exceeding limit value

0.0% (no detection)

0.1%-300.0% (Motor rated

current)

Adjust the value based on the

site requirement

F8-37

Output current

exceeding

limit detection delay

time

0.00s-600.00s

Adjust the value based on the

site requirement

■

When power fails during the Elevtaor operation, the UPS/ARD provide temporary

power supply to the Elevator controller which routes the UPS/ARD power supply to

MD500L inverter also for Elevator rescue operation.

■

When door is fully closed and safeties are connected/closed, the elevator controller

does the rescue function which provides Up/Down direction command and Rescue

speed reference command to the MD500L inverter to run the machine. Elevator

opens/enables the Brake and starts to run in rescue speed set in the inverter (FC-08)

to the rescue floor.

■

If Elevator controller detect the least current direction by running the machine

in both direction for some distance to check the machine drawing current by its

rescue logic or with help of MD500L inverter function (F5-05=36 Software current

exceeding limit), then the rescue direction will be selected in least current direction

by the elevator controller in UPS/ARD rescue mode.

■

Providing Least current direction running in UPS/ARD mode consume lesser

Battery energy.

■

After Elevator reaching Rescue floor, elevator controller withdraws the commands

to the MD500L inverter and stops the elevator by applying the brake on machine

and opens the doors.

Содержание Aonarch MD500L Series






































































Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды

Inovance Aonarch MD500L Series, Руководство пользователя

Результаты поиска

Содержание Aonarch MD500L Series

Отзывы:

Похожие инструкции для Aonarch MD500L Series

Бренды по названию

Популярные бренды