Ingersoll-Rand A951X040BD3SAB, Руководство по установке

Страница: 30 / 104

30
88-A951X001-1D-EN
ATTACHING VENT PIPING
Important: Products installed in Canada must use vent systems that
are certified to the Standard for Type BH Gas Venting
Systems (ULC S636) for Class II-A venting systems (up
to 65°C). Components of the vent system must not be
interchanged with other vent systems or unlisted pipe or
fittings. Plastic components, specified primers, and glues
must be from a single system manufacturer and not
intermixed with other system manufacturer's vent
system parts. In addition, the first three feet of the vent
pipe must be visible for inspection.
PIPE JOINTS: All joints must be fastened and sealed per manufacturer
instructions and local and national codes to prevent escape of
combustion products into the building.
MANUFACTURED MODULAR VENTING SYSTEMS
W WA AR RN NIIN NG G
C CA AR RB BO ON N M MO ON NO OX XIID DE E P PO OIIS SO ON NIIN NG G
H HA AZ ZA AR RD D!!
F Fa aiillu urre e tto o ffo ollllo ow w tth hiiss W Wa arrn niin ng g m ma ay y rre essu ulltt iin n p prro op pe errtty y
d da am ma ag ge e,, sse ev ve erre e p pe errsso on na all iin njju urry y,, o orr d de ea atth h..
S Se ee e tth he e A Ap pp prro ov ve ed d V Ve en ntt P Piip pe e M Ma atte erriia allss tta ab blle e ffo orr
m ma an nu uffa accttu urre ed d m mo od du ulla arr v ve en nttiin ng g ssy ysstte em mss tth ha att a arre e
a ap pp prro ov ve ed d ffo orr u usse e w wiitth h tth hiiss p prro od du ucctt.. F Fo ollllo ow w tth he e
m ma an nu uffa accttu urre err’’ss iin nsstta alllla attiio on n iin nssttrru uccttiio on nss w wh he en n
iin nsstta alllliin ng g tth he e v ve en nttiin ng g ssy ysstte em m..
W WA AR RN NIIN NG G
C CA AR RB BO ON N M MO ON NO OX XIID DE E P PO OIIS SO ON NIIN NG G
H HA AZ ZA AR RD D!!
F Fa aiillu urre e tto o ffo ollllo ow w tth hiiss W Wa arrn niin ng g m ma ay y rre essu ulltt iin n p prro op pe errtty y
d da am ma ag ge e,, sse ev ve erre e p pe errsso on na all iin njju urry y,, o orr d de ea atth h..
D Do o n no ott u usse e cce em me en ntt o on n p po olly yp prro op py ylle en ne e v ve en nttiin ng g
ssy ysstte em mss.. F Fo ollllo ow w tth he e m ma an nu uffa accttu urre err’’ss iin nsstta alllla attiio on n
iin nssttrru uccttiio on nss w wh he en n iin nsstta alllliin ng g tth he e v ve en nttiin ng g ssy ysstte em m..
For manufactured modular venting systems that are approved with
this product see PVC vent fitting material table. Do not drill into
polypropelene venting pipes
BONDING OF PVC
Note: It is recommended that the first joints from the Furnace be
connected and sealed with high temperature RTV. This will
enable the pipes to be removed later without cutting.
Be sure to properly support these joints.
Commercially available solvent cement for PVC must be used to join
PVC pipe fittings. Follow instructions on container carefully.
Pipe and Fitting – ASTM D1785, D2466, D2661, & D2665
PVC Primer and Solvent Cement – ASTM D2564
Procedure for Cementing Joints – Ref ASTM D2855
1. Cut pipe square, remove ragged edges and burrs. Chamfer end of
pipe, then clean fitting socket and pipe joint area of all dirt,
grease, moisture or chips.
2. After checking pipe and socket for proper fit, wipe socket and pipe
with cleaner-primer. Apply a liberal coat of primer to inside
surface of socket and outside of pipe.
DO NOT ALLOW PRIMER TO DRY BEFORE APPLYING CEMENT.
3. Apply a thin coat of cement evenly in the socket. Quickly apply a
heavy coat of cement to the pipe end and insert pipe into fitting
with a slight twisting movement until it bottoms out.
4. Hold the pipe in the fitting for 30 seconds to prevent tapered
socket from pushing the pipe out of the fitting.
5. Wipe all excess cement from the joint with a rag. Allow 15
minutes before handling. Cure time varies according to fit,
temperature and humidity.
Connection of the pipe and collar of the combustion air inlet should
just be a friction fit. It is recommended that the inlet air joint be sealed
with RTV type sealant to allow the joint to be separated for possible
future service. The inlet and vent pipes must be properly supported
throughout the entire length.
Note: Follow venting instructions carefully when using PVC cement.
Important: All joints must be water tight. Flue condensate is
somewhat acidic, and leaks can cause equipment
damage.
Seal
INLET AIR PIPE
with RTV sealant
F Fu urrn na acce e G Ge en ne erra all IIn nsstta alllla attiio on n