manualshive.com logo in svg

Infoblox Infoblox-4030, Инструкции по установке, Страница: 20 / 24

Поделиться
Скачать
Infoblox Infoblox-4030 Скачать руководство пользователя страница 20

Copyright ©2018, Infoblox, Inc.All right reserved.

1.  
2.  
3.  

4.  

5.  
6.  

1.  
2.  
3.  
4.  

5.  

6.  
7.  

To replace an Infoblox-4030/Infoblox-4030-10GE AC power supply, do the following:

Turn off the power supply.
Disconnect the AC power cable from the power outlet.
Gently push back the red catch-release lever, grip the power supply handle, and pull the power supply unit out of the chassis as
illustrated in 

.

Figure 14

Place the replacement power supply into the bay and push it forward until it is fully seated in the chassis. The catch-release lever will
gently click into place.
Reconnect the power cable.
Turn on the power supply. If it is fully seated, powered on, and operating properly, the LED glows steady green.

Changing DC Power Supplies

:

WARNING

 

 

 

 

 

 

 

 

 

 

 

 

 

When installing a DC power supply, connect the ground wire to the PSU before connecting the positive or negative leads. Ensure that

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 

you use the correct polarity when connecting power leads to the PSU. Always remove power from the power supply before performing any install

   

 

   

 

 

ation or replacement steps or maintenance of the power supply.

In DC power configuration, the Infoblox-4030 and Infoblox-4030-10GE appliances ship with two redundant, auto-switching DC power supplies.
The power supplies are "hot-swappable", so you can remove or replace one power supply without interrupting appliance operation and network
services.
To replace an Infoblox-4030/Infoblox-4030-10GE DC power supply, do the following:

Disconnect the DC power cable from the power outlet on the external transformer.
Disconnect the power cable from the power supply.
Disconnect the ground cable from the power supply.
Gently push back the red quick-release lever, grip the power supply handle, and pull the power supply unit out of the chassis, as shown
in 

.

Figure 15

Place the replacement power supply into the bay and push it forward until it is fully seated in the chassis. The red catch-release lever will
gently click into place.
Connect the ground cable to the new power supply.
Connect the power cable, ensuring that you use the correct polarity. If the power supply is fully seated and operating, the LED glows
steady green.

 

 

 

 

Figure 15 Removing an Infoblox-4030/Infoblox-4030-10GE DC Power Supply

Содержание Infoblox-4030

























Отзывы:

Нет отзывов