background image

Copyright ©2018, Infoblox, Inc.All right reserved.

3.  Log in using the default user name and password 

 and 

.

admin

infoblox

Note: User names and passwords are case-sensitive.

4. Read the Infoblox End-User License Agreement and click   

 to proceed if you agree with the terms and conditions.

I Accept

5. The Setup Wizard opens, and you can enter basic network and deployment settings.

Determine how you want to deploy the appliance, and then use the following worksheets to note the network settings that you want to enter
on the wizard screens.

Use the following worksheet when configuring a single independent appliance or Grid member:

Settings

Enter your information here

Grid Name

Shared Secret Host Name

LAN1 Port IP Address and Netmask

Gateway IP Address

On the last screen of the wizard, click 

. The Infoblox GUI application restarts. 

Finish

Infoblox CLI

The Infoblox CLI allows you to configure and monitor the appliance using a small set of Infoblox commands. Some tasks, such as resetting the
appliance, can only be done through the CLI. You can access the Infoblox CLI through a direct console connection from your management
system to the Infoblox appliance. (For more information, see 

.) You can also enable remote console access — that is, SSHv2

 

 

Console Port

(Secure Shell version 2) access— through the Infoblox GUI or CLI, and then access the CLI from a remote location using an SSHv2 client. (For
more information, refer to the 

 

 

 

.)

Infoblox NIOS Administrator Guide

Using CLI Help

You can display a list of available CLI commands by typing help at the command prompt.

Infoblox > help

==============================================================================

CommandSummary

==============================================================================

?                       Display help

delete                  Delete files

dig                     Perform a DNS lookup and print the results

exit                    Exit command interpreter

help                    Display help

ping                    Send ICMP ECHO

quit                    Exit command interpreter

reboot                  Reboot device

reset                   Reset system settings

set                     Set current system settings

show                    Show current system settings

shutdown                Shutdown device

traceroute              Route path diagnostic

Содержание Infoblox-4030

























Отзывы: