241
Input data for 4 channels per slave ......................................... 70
Instructions ............................................................................ 233
Intended use.......................................................................... 233
IO-Link ................................................................................... 233
IP address ............................................................................. 233
Jitter....................................................................................... 234
LAS........................................................................................ 234
LDS........................................................................................ 234
LED........................................................................................ 234
LED [module status] .............................................................. 218
LED [network status] ............................................................. 218
LFS ........................................................................................ 234
Link ........................................................................................ 234
List of periphery faults (LPF) on AS-i master 1 ....................... 86
List of periphery faults (LPF) on AS-i master 2 ....................... 87
List of projected slaves (LPS) on AS-i master 1...................... 87
List of projected slaves (LPS) on AS-i master 2...................... 87
List of the configuration errors on AS-i master 1..................... 86
List of the configuration errors on AS-i master 2..................... 87
LKCS ..................................................................................... 234
LNACS................................................................................... 234
LPS........................................................................................ 234
LSB........................................................................................ 234
MAC-ID.................................................................................. 234
Main menu [Fieldbus Setup].................................................. 220
Main menu [Quick Setup] ...................................................... 219
Master.................................................................................... 234
Master flags in module 11 ....................................................... 92
Master-slave communication................................................. 234
MBd ....................................................................................... 235
Menu...................................................................................... 219
MMI........................................................................................ 235
Modbus.................................................................................. 235
Module 1 – digital input master 1(A)........................................ 39
Module 10 – analogue multiplexed output............................... 57
Module 11 – fieldbus data command channel......................... 61
Module 11, command 1 – read master flags........................... 91
Module 11, command 10dec (0Ahex) – read LPF
(list of slaves with periphery fault) ................................... 108
Module 11, command 11dec (0Bhex) – read LPS
(list of projected slaves)................................................... 110
Module 11, command 13dec (0Dhex) – read telegram
error counter .................................................................... 112
Module 11, command 14dec (0Ehex) – read configuration
error counter .................................................................... 114
Module 11, command 15dec (0Fhex) – read AS-i
cycle counter.................................................................... 116
Module 11, command 16dec (10hex) – change current
slave parameters ............................................................. 118
Module 11, command 19dec (13hex) – project all ................ 120
Module 11, command 2 – change operating mode................. 93
Module 11, command 21dec (15hex) – save configuration
in flash ............................................................................. 122
Module 11, command 22dec (16hex) – reset telegram
error counter of a slave.................................................... 124
Module 11, command 3 – read current slave configuration .... 94
Module 11, command 4 – read projected slave
configuration ...................................................................... 96
Module 11, command 5 – change projected slave
configuration ...................................................................... 98
Module 11, command 6 – read slave parameters................. 100
Module 11, command 7 – change projected slave
parameters....................................................................... 102
Module 11, command 8 – read LAS (list of active slaves) .... 104
Module 11, command 9 – read LDS (list of detected
slaves) ............................................................................. 106
Module 12 – fieldbus data PLC input ...................................... 63
Module 13 – fieldbus data PLC output .................................... 66
Module 14 – analogue input master 1 ..................................... 69
Module 15 – analogue output master 1................................... 76
Module 16 – analogue input master 2 ..................................... 83
Module 17 – analogue output master 2................................... 84
Module 18 – fieldbus diagnostic data ...................................... 85
Module 19 – host command channel ...................................... 88
Module 19, command 00dec (00hex) – no execution of
a command...................................................................... 132
Module 19, command 01dec (01hex) – write parameters
to an AS-i slave (change current slave parameters) ....... 134
Module 19, command 03dec (03hex) – adopt and save
currently connected AS-i slaves in the configuration........ 138
Module 19, command 04dec (04hex) – change the list
of projected AS-i slaves (LPS)......................................... 141
Module 19, command 05dec (05hex) – set the operating
mode of the AS-i master.................................................. 144
Module 19, command 06dec (06hex) – readdress
a connected AS-i slave.................................................... 147
Module 19, command 07dec (07hex) – set the auto
address mode of the AS-i master.................................... 150
Module 19, command 09dec (09hex) – change
extended ID code 1 in the AS-i slave .............................. 152
Module 19, command 102dec (66hex) – retrieve
the status of the device display ....................................... 209
Module 19, command 105dec (69hex) – read the
properties of the device ................................................... 215
Module 19, command 21dec (15hex) – read the ID string
of an AS-i slave with the profile S-7.4.............................. 161
Module 19, command 28dec (1Chex) – no slave reset
when changing to the protected mode ............................ 165
Module 19, command 31dec (1Fhex) – one-time
execution of the extended safety monitor protocol
in the Safety-at -Work monitor......................................... 167
Module 19, command 33dec (21hex) – read the
diagnosis string of an AS-i slave with profile S-7.4 ......... 172
Module 19, command 34dec (22hex) – read the
parameter string of an AS-i slave with the profile S-7.4 .. 175
Module 19, command 35dec (23hex) – write parameter
string of an AS-i slave with the profile S-7.4.................... 178
Module 19, command 50dec (32hex) – read current
configuration AS-i slaves 0(A)...15(A) ............................. 181
Module 19, command 51dec (33hex) – read current
configuration AS-i slaves 16(A)...31(A) ........................... 184
Module 19, command 52dec (34hex) – read current
configuration AS-i slaves 0...15B..................................... 186
Module 19, command 53dec (35hex) – read current
configuration AS-i slaves 16B...31B ................................ 188
Module 19, command 54dec (36hex) – read current
parameters of the AS-i slaves ......................................... 190
Module 19, command 55dec (37hex) – read current
AS-i slave lists ................................................................. 193
Module 19, command 56dec (38hex) – read projected
configuration AS-i slaves 1(A)...15(A) ............................. 196
Module 19, command 57dec (39hex) – read projected
configuration AS-i slaves 16(A)...31(A) ........................... 199
Module 19, command 58dec (3Ahex) – read projected
configuration AS-i slaves 1B...15B .................................. 201
Module 19, command 59dec (3Bhex) – read projected
configuration AS-i slaves 16B...31B ................................ 203
Module 19, command 96dec (60hex) – save data non-
volatilely in the flash memory of the device...................... 205
Module 19, command 97dec (61hex) – carry out various
settings in the device ....................................................... 207
Module 19, commands 10...20dec (0A...14hex) – force
analogue data transmission directly to / from
3 AS-i slaves each........................................................... 156
