IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 171

IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 94

70

1693 RLC Digibridge

Operation

3.9.3 Summary of Interrogations

Certain status (and results) information is indicated

automatically on the display panels. For example:

Indicators above and below RLC display ─ param-

eter and /or units of measurement.
RANGE HELD ─ autoranging is disabled.
CONST VOLT ─ source resistance held to 25 ohms

(accuracy compromised).
PPM ─ units of D or Q, ANG (not R or X) are parts

per million.
CONST I ─ short circuit current set .
NOT 1KHZ ─ frequency is other than 1 kHz.
RATIO ─ ratio mode is enabled.
Hardly any keyboard indicators lit ─ keyboard is

locked.
Left display “0”, right also “0”, GO ─ open-circuit

zeroing enabled.
Left display “5”, right also “5”, GO ─ short-circuit

zeroing enabled.
Left display “6”, right also “6”, GO ─ calibration

enabled.
Left display “0 14 ‘’, right “blank” ─ measurement

signal overload .
Left display “22222”, right “1111” ─ convertor/

detector malfunction.
Left display “22222”, right “2222” - convertor/

detector malfunction.

The preceding three lines are explained in paragraph

3.13. Indicators on the keyboard provide important

information, NOT summarized here.

The following interrogations will work only if you

select ENTER function:

[SHIFT] [NOM VAL]

stored nominal value (appears displayed

at left).

[SHIFT] [BIN NO] [0] [1]

limits for bin 1 (both displayed , left and

right) .

[SHIFT] [BIN NO] [1] [2]

limit s for bin 12 (both displayed).

[SHIFT] [BIN SUM] [0] [3]

count in bin (left) ; bin number (right) .

[SHIFT] [FREQUENCY]

test frequency , kHz (displayed a t left).

[SHIFT] [CONST I]

short circuit current if selected .

[SHIFT] [VOLTAGE]

test voltage that is applied behind source

resistance .

[SHIFT] [AVERAGE]

number of measurements (or medians)

averaged per result .

The following special functions are explained more

fully in paragraph 3.10.

Each response display is: detailed code at left and

special-function number at right.

Interrogation

Detail Code

[SHIFT][SPECIAL][1]

present range number

[SHIFT][SPECIAL][2]

Code for data output via IEEE-488 bus

[SHIFT][SPECIAL][3]

Measurement routine

[SHIFT][SPECIAL][4]

Milliseconds of delay after start before data

is acquired

[SHIFT][SPECIAL][5]

Integration time factor (normal: 1)

[SHIFT][SPECIAL][6]

Displays – meas/nom: 2, nom/meas: 1,

normal: 0

[SHIFT][SPECIAL][7]

Parameter selection – auto: 1, normal: 0

[SHIFT][SPECIAL][8]

If median of 3 meas taken: 1, normal: 0

[SHIFT][SPECIAL][9]

Version number of Digibridge internal

firmware

[SHIFT][SPECIAL][0]

ppm offset of source frequency from nominal

[SHIFT][SPECIAL][.]

IEEE-488 address (2 digit) when this option

is installed

The following interrogation will work only if you

select MEASURE function:

[SHIFT][SPECIAL] (hold key down) – All special

functions

Expect 0,1,4 and 9 (see above) that are NOT set to “0”.

For example, under default (power up) conditions,

the display is **** *7* (where * represents “blank”)

NOTE: special function 7 is initially set to 1; see

Table 2-12. If you set special functions 2 through 8

each to 1, this display will be 2315 678. If you set

these special functions each to 0, this display will be

**** *** (blank).

«
...
92
93
94
95
96
...
»

Содержание RLC Digibridge 1693












































































































































































Отзывы:

Нет отзывов