IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 46

Страница: 46 / 171

1693 RLC Digibridge

Operation

3.2.7 7000-05 Tweezers

The 7000-05 tweezers combine the two functions:

• They handle chip components, up to 0.5 in.

(12 mm) thick.

• Serve as a test fixture for measuring these com-

ponents, if their terminals are on opposite faces.

The 7000-05 Chip Component Tweezers can handle

small unleaded “chips” or SMDs (surface mounted

devices), passive sensors, and components for test-

ing on the Digibridge. A four-terminal Kelvin con-

nection extends to the tip of the tweezers where the

measurement becomes two-terminal, therefore series

impedance of the connecting cables and internal

tweezer connections do not affect the measurement.

The small amounts of residual-tip resistance and

inductance can be automatically corrected by using

the Digibridge shorting function with the tips pressed

together. Guard shields between the tweezer blades

minimize capacitance between them. A correction for

this small capacitance can be made using Digibridge

open circuit test with the tips held at a spacing equal

to that of the component’s contact spacing.

Figure 3-13: 7000-05 Chip Component

Tweezers

For this accessory an additional accuracy (for param-

eters listed) must be added to the standard instrument

accuracy as defined by AutoAcc.

C: ± 1.5 pF

R: ± 10 mΩ

L: ± 100 nH

Q: for R > 100 Ω, ±(9 * Freq * R * 10

-12

ppm)

Q; for R ≤ 100 Ω, ±((R/Freq) * 10

-6

ppm)

Measurement accuracy is very sensitive to connection

geometry. The same connection geometry must be

used for open/short compensation as for connection

to the device under test.

Connection to Digibridge:

Connect to

Digibridge

Cable Marking

Connection to DUT

PH (potential, high)

to positive (+) terminal

of DUT

IH (current, high)

HD/HF

PL (potential, low)

to negative (-) terminal

of DUT

IL (current, low)

LD/LF

The PH (HS) and IH (HD/HF) cables connect to the

fixed arm of the tweezers (+) and the PL (LS) and

IL (LD/LF) cables connect to the movable arm of

the tweezers (-). To ensure valid measurements it is

especially important to observe the correct polarity

when DC bias is to be used.

If dc bias is used (see paragraph 3.7), note that the

fixed arm of the tweezers is positive and the movable

arm is negative.

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 46 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: