IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 114

Страница: 114 / 171

1693 RLC Digibridge

Operation

Description:

Sets the OPC bit (bit 0) of the Standard Event

Status Register when all pending operations have

completed or ended.

Equivalent legacy command:

none

Equivalent key:

none

*RST

Syntax:

*RST

Description:

Resets Digibridge settings to Turn-On Conditions.

Equivalent legacy command:

Equivalent key:

none

*SRE

Syntax:

SRE <numeric>

*SRE?

Description:

Sets the value of the Service Request Enable

Service Request Enable Register.

Parameter:

Value

Description

0 to 255

Numeric value range

Equivalent legacy command:

none

Equivalent key:

none

*STB?

Syntax:

*STB?

Description:

Reads the value of the Status Byte register.

Equivalent legacy command:

none

Equivalent key:

none

*TST?

Syntax:

*TST?

Description:

Initiates self-test and returns 0 if all tests passed or

error code if any test failed.

Equivalent legacy command:

none

Equivalent key:

none

*WAI

Syntax:

*WAI

Description:

Waits until all commands previously sent have

completed.

Equivalent legacy command:

none

Equivalent key:

none

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 114 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: