IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 146

Страница: 146 / 171

122

1693 RLC Digibridge

Service and Maintenance

3. Remove the interface option (or the blank

cover plate) horizontally, directly away from

the front panel.

To install the interface option, proceed as follows:

1. Hold the interface option by its rear panel,

so that the labels near the connectors read

“right-side up.”

If you look through the opening in the rear, you will see

an open connector. The contact edge of the interface

board is going to have to slide in there.

2. Press the interface fully into the Digibridge

by hand, confirming that alignment is correct.

3. Reinstall the screws.

5.5.4 Removal of Multiple-Pin

Packages

Use caution when removing a plug-in integrated-

circuit or other multiple-pin part, not to bend pins

nor stress the circuit board. Withdraw the part straight

away from the board. Unless an IC is known NOT to

be a static sensitive type, place it immediately on a

conductive pad (pins in the pad) or into a conductive

envelope.

DO NOT attempt to remove a soldered-in IC package

unless you have the proper equipment and skills to

do so without damage.

CAUTION

Observe precautions while handling
the interface option. Because there
are static sensitive parts on the board,
DO NOT TOUCH THE CIRCUITS or ICs.
Refer to Section 5 of this manual, for

recommended handling procedure.

5.6 Periodic Maintenance

5.6.1 Care of Test Fixtures

For best results and minimum maintenance effort, the

operator must remove any obvious dirt from leads

of DUTs before inserting them into any test fixture.

Test fixture contacts will wipe through a thin film of

wax, but they can become clogged and ineffectual if

the operator is careless about cleanliness. The unit

should be cleaned monthly with a soft brush and

isopropyl alcohol. Avoid getting excess alcohol on

painted surfaces to avoid possible damage. The test

fixture and its axial adaptors should be cleaned once

a year as follows:

1. Use compressed air to blow away any dust

on the surface as well as inside the fixture.

2. Clean the contact surfaces and blades of the

axial-lead adaptors with isopropyl alcohol.

Rub with a cotton swab (Q-tip). Remove

any remaining alcohol with compressed air,

and remove any remaining cotton fibers with

tweezers.

5.6.2 Care of the Display Panel

Use caution when cleaning the display window, not to

scratch it or to get cleaning substances into the instru-

ment. Use a soft cloth, a lint-free wiper, or absorbent

cotton moistened with a mild glass cleaner, such as

plain Windex.

DO NOT

use paper towels.

If it becomes necessary to place marks on the win-

dow, use paper-based masking tape (NOT any kind of

marking pen, which could be abrasive or react chemi-

cally with the plastic). To minimize retention of any

gummy residue, remove the tape within a few weeks.

Figure 5-9: Screws holding the interface assembly on the rear panel

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 146 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: