IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 33

Страница: 33 / 171

1693 RLC Digibridge

Installation

use of line-voltage regulators between power lines

and the test equipment is recommended as the only

sure way to rule out the effects on measurement data

of variations in line voltage.

2.5 Test-Fixture Connections

An external test fixture or cables are always required,

because connection from the 1693 Digibridge to the

DUT is provided via BNC cables (from connectors

that can be positioned at either front or rear of the

instrument, as described .in Chapter 5). For general

purposes, the recommended test fixture, cable, and

their connections are as follows. Refer to paragraphs

1.4 and 3.2 for more information about accessories.

On 1693

Description

Cable

Drive -

Black Band

I+

Potential -

Black and

White Band

P+

Pot

Red and White

Band

P-

Drive +

Red Band

I-

COMMENT: It is important that the IL and PL leads

connect to the same end of the DUT (and that PH and

IH connect to the other end). Also, connecting IL/PL

to the test-fixture connectors labeled “+” (and IH/PH

to “-”) assures that the test fixture’s “+”and “0” labels

agree with the bias polarity.

NOTE: In the cable’s color code, RED is associated

with “hot” leads, which have dc voltage, negative

with respect to ground , when bias is used.

2.6 Bias Voltage for the DUT

2.6.1 Internal Bias

No external connections are required for the internal

2-volt bias. 2V bias is supplied internally by the

instrument.

2.6.2 External Bias

External bias can be provided by connecting a suitable

current-limited, floating dc voltage source, as follows.

• Be sure that the voltage is never more than

60 V, max.

• A current limiting voltage supply is recom-

mended; set the limit at 200 mA, max.

• Be sure that the bias supply is floating; DO

NOT connect either lead to ground.

• A well-filtered supply is recommended. Bias-

supply hum can affect some measurements,

particularly if test frequency is the power

frequency.

• Generally the external circuit must include

switching for both application of bias after each

DUT is in the test fixture and discharge before

it is removed.

• Connect the external bias voltage supply and

switching circuit, using the optional 1658-2450

cable, via the rear-panel EXTERNAL BIAS

connector. Observe polarity marking on the rear

panel; connect the supply accordingly.

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 33 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: