IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 25

Страница: 25 / 171

1693 RLC Digibridge

Introduction

Chapter 1

INTRODUCTION

1.1 Purpose

The 1693 RLC Digibridge™ is a microprocessor-

controlled, automatic, programmable RLC measuring

instrument that provides high accuracy, convenience,

speed , and reliability at low cost. Limit comparison,

binning, and internal bias are provided; both test fre-

quency and voltage are selectable. With an interface

option, the Digibridge tester can communicate with

other equipment via IEEE-488 bus and respond to

remote control.

The versatile, adaptable test fixture, lighted keyboard,

and informative display panel makes the Digibridge

tester convenient to use. Measurement results are

clearly shown with decimal points and units, which

are automatically presented to assure correctness.

Display resolution is 5 full digits for R, L, C, G,

Z, and Y (4 full digits for D, Q, R, X, B, and ANG.

Notice that R is also known as ESR (equivalent series

resistance).

The basic accuracy is 0.02%. Long-term accuracy and

reliability are assured by the measurement system,

which makes these accurate analog measurements

over many decades of impedance without any critical

internal adjustments. Calibration to account for any

change of test-fixture parameters is semiautomatic;

the operator needs to provide only open-circuit and

short- circuit conditions in the procedure. The

Digibridge tester normally autoranges and automati-

cally identifies the principal measurement parameter.

The optional test fixture 1689-9600, with a pair of

plug-in adaptors, receives any common component

part (axial-lead or radial-lead), so easily that insertion

of the device under test (DUT) is a one-hand opera-

tion. True 4-terminal connections are made automati-

cally. Extender cables are available for measurements

at a moderate distance from the instrument.

Limit comparisons facilitate sorting into 13

and

NO-GO

bins.

• Test frequencies from 12 Hz to 200 kHz

• Test voltages from 5 mV to 1.275 V; bias (2 V)

• Delay (before data acquisition) from zero to

99999 ms

• Measurement speeds up to 30 per second

• Multi-measurement routines with automatic

averaging and/or median taking of 2 to 255

measurements.

• Displays: measured values , percentages, dif-

ferences, ratios, GO/NO-GO, binning

• Automatic output of value , bin number, bin

summary and other results via IEEE-488 bus

Bias can be applied to capacitors being measured,

either by programming the selection of an internal

supply (2 V) or by sliding a switch to connect an

external voltage source (up to 60 V).

A choice between two interface options provides full

“talker/listener” and “talker only” capabilities consis-

tent with the standard IEEE-488 bus . (Refer to the

IEEE Standard 488-1978, Standard Digital Interface

for Programmable Instrumentation.)

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 25 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: