IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 143

Страница: 143 / 171

119

1693 RLC Digibridge

Service and Maintenance

7. To remove the keyboard module:

A. Remove the four screws (all with their

heads to the right) that hold the keyboard

assembly to the subpanel at the right and

the keyboard bracket at the left. Remove

this assembly.

B. To separate the keyboard, remove 4 screws

that pass through the mounting plate.

Reassembly note: Be sure that all keys and switches

of the keyboard are properly located in their holes

in the subpanel before tightening the four screws in

the subpanel and bracket. Also, plug the two cables

into the keyboard before attaching the front-panel

assembly to the chassis.

IMPORTANT: each of these cables plugs onto a

row of pins, without any keying. Be sure that the

cable is oriented correctly (with color marked

edges

at the keyboard and

toward the rear

at the

main board.

Also

be sure that each cable connector

engages its full set of pins and does NOT miss the

first or last one.

8. To remove the display board:

A. Remove the two screws that pass through

the display board, into spacers on the sub-

panel (not the two screws that fasten the

associated connector board). .

B. Slide the display board upwards, to unplug

it from the connectors below.

9. To remove the main board:

A. Disconnect the cables that connect this

board with display, keyboard, and power

supply. (See above.)

B. Remove the two screws from below that

attach the bnc-connector bracket (at the

front or rear panel).

C. Remove eight screws from above that

fasten the main board to the chassis and

the stiffener below this board. Note: One

of these screws is accessed after first re-

moving the air deflector (2 screws) near

the right rear air vent.

D. Remove the main board, forward and

upwards. If removal is obstructed by the

front-panel assembly, that can be removed

first. (See above.)

5.5.1 Relocation of bnc Connector

Bracket

The bnc connectors that interface (via cables) with

the DUT test fixture can be located at the lower part

of either front or rear panel. The four bnc connectors

remain mounted on their bracket and cabled to the

main board during relocation from front to rear, or

vice versa. To relocate this bracket from front to rear:

1. Loosen generously (but do NOT remove) the

two right-side screws that fasten the front-

panel assembly into the chassis. Stand the

instrument on its right side. Remove the two

left-side screws that are opposite to the ones

just loosened. Now the front-panel assembly

can be tipped away from the instrument an

inch or two (as required in the next step).

Note: the display and keyboard cables remain connected.

2. Remove the blank bracket (2 screws) from

the rear bnc-connector position.

3. Remove the two screws that fasten the bnc

connector bracket to the main chassis, below

the front panel.

4. Holding the front-panel assembly tipped

away from the instrument slightly, snake

the bnc connector bracket between the main

board and the nearby part of the chassis, until

free from its front position. Return the front-

panel assembly to its normal position and

secure it with its two screws.

If necessary,

loosen but DO NOT REMOVE the screws

holding the mother board.

5. Snake the bnc connector bracket carefully

into the rear position (where the blank bracket

was).

CAUTION

Handle the shielded cable assembly
with care and be sure that it is
dressed neatly, with a minimum of

twist or stress in its new position.

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 143 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: