IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 152

Страница: 152 / 171

128

1693 RLC Digibridge

Service and Maintenance

5.7.4 Power Supply and Regulator

Board

To verify that the power supply (700011-4) is work-

ing properly, confirm the following voltage outputs

(See Figure 5-12).

• Red to black wire = +5 V (±0.2 V)

• Yellow to black wire = +12 V (±0.8 V)

• Blue to black wire = -12 V (±0.6 V)

To verify that the regulator board (750023) is work-

ing properly, confirm the following voltage outputs

(See Figure 5-12).

+5 V Digital
GND Digital
+5 V Analog
-8 V Analog
GND Analog
GND Analog
-8 V Analog
+5 V Analog
GND Digital
+5 V Digital

Regulator Board Test Points

Power Supply Test Points

Figure 5-12: Power Supply and Regulator Board Test Points

For replacement Power Supply Assembly, contact IET Labs.

+5 V values (±0.2 V)

• Pin 1 to Pin 2

• Pin 3 to Pin 5

• Pin 8 to Pin 6

• Pin 10 to Pin 9

-8 V values (±0.4 V)

• Pin 4 to Pin 5

• Pin 7 to Pin 6

CAUTION

To prevent damage to the unit, avoid

short-circuiting the pins.

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 152 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: