IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 116

Страница: 116 / 171

1693 RLC Digibridge

Operation

Character

Sequence

Purpose

Allowed

Characters

Meaning

Status

(space)

Normal Operation

Underrange held (reduced accuracy)*

Overrange held (reduced accuracy)*

End extension of range 1 or 1 (reduced accuracy)**
Invalid measurement due to signal overload

Value of delta RLC or

ratio

(space)

Normal display

Delta RLC Mode

Ratio Mode: Nominal Value/RLC Value

Parameter

Inductance

Capacitance

Resistance

Conductance

Impedance

Admittance

Normal or ratio mode

(space)

Normal mode (one of 3 describe above)

Ratio Mode: RLC Value/Nominal Value

5,6

Units

(space)H

Henries

Millihenries

Microfarads

Nanofarads

(space)S

Siemens

Millisiemens

Microsiements

(space)%

Percent difference from nominal value

(space)Ω

Ohms

kΩ

kiloohms

Format

(space)

Sign

(space)

Positive Value

Negative Value

9...15

Number

0123456789.

(space)

Measured number, right justified in format field, like the

RLC display except the zero before the decimal point is

explicitly provided and this number can be as long as seven

characters. ***

(CR)

The standard “carriage return” and “line feed” characters;

end of string.

(LF)

Table 3-21: Data output format for RLC value, delta%, deltaRLC, or RATIO

* Underrange generally occurs when the measured impedance is lower than the nominal low limit (for automatic range change)

and there is a lower-impedance range. Overrange generally occurs when the measured impedance is higher than the nominal

high limit (for automatic range change) and there is a higher-impedance range. In either case, an appropriate range change

will improve accuracy. If there is no appropriate range to change to, the status is “range end ex tension “; see below. Range

limits are different if CONSTANT VOLTAGE OR CONSTANT CURRENT has been selected; see paragraph 3.5.6.

** Range 1 end extension if DUT impedance exceeds that of the largest R or L (smallest 0) in basic range 1. Range 4 end

extension if DUT impedance is less than that of the smallest R or L (largest 0) in basic range 4. No possibility of changing range

to improve accuracy.

*** If the measurement is outside of the display range (display goes blank), 9999999 is output in this numeric field.

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 116 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: