IET Labs, Inc. RLC Digibridge 1693 Скачать руководство пользователя страница 3

Страница: 3 / 171

TEL: (516) 334-5959 • (800) 899-8438 • FAX: (516) 334-5988

534 Main Street, Westbury, NY 11590

IET LABS, INC.

www.ietlabs.com

Standards • Decades • Strobes • Sound Level Meters • Bridges

1693 RLC Digibridge

WARRANTY

We warrant that this product is free from defects in material and workmanship and, when properly used,

will perform in accordance with applicable IET specifi cations. If within one year after original shipment,

it is found not to meet this standard, it will be repaired or, at the option of IET, replaced at no charge when

returned to IET. Changes in this product not approved by IET or application of voltages or currents greater

than those allowed by the specifi cations shall void this warranty. IET shall not be liable for any indirect,

special, or consequential damages, even if notice has been given to the possibility of such damages.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,

INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR ANY PARTICULAR PURPOSE.

Содержание RLC Digibridge 1693












































































































































































Результаты поиска

Содержание RLC Digibridge 1693

Отзывы:

IET Labs, Inc. RLC Digibridge 1693, Руководство пользователя и обслуживания, Страница: 3 / 171

Результаты поиска

Содержание RLC Digibridge 1693

Отзывы: