IDT CPS-1848 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 450

background image

6. Event Management > Event Management Overview

CPS-1848 User Manual

109

June 2, 2014

Formal Status

This document is confidential and is subject to an NDA.

Integrated Device Technology

6.1.2

Physical Layer Error Management Overview

The CPS-1848 can detect many types of physical layer errors. Physical layer errors are grouped into “Standard” physical layer
errors, which are defined by the RapidIO Interconnect Specification (Revision 2.1), Part 8 Error Management Specification,
and “Implementation Specific” errors, which are specific to IDT devices. These two types have slightly different programming
models, as displayed in

.

Standard physical layer errors are always indicated in the

Port {0..17} Error Detect CSR

. When enabled in the

Error Rate Enable CSR

, error information is captured for the events in the four error capture registers,

Port {0..17} Capture 0

Port {0..17} Capture 3 CSR

; enabled events are also counted. If the event counts exceed the threshold values

programmed in the

Port {0..17} Error Rate Threshold CSR

, additional events are detected and isolation can be triggered.

Events enabled in the

Port {0..17} Error Report Enable Register

can be reported to software using port-writes or interrupts, or

captured in the error log, depending on the configuration of the registers displayed in

.

Figure 20: Standard Physical Layer Error Management Programming Model Flow Chart

Port-writes and interrupts are disabled by default for individual Standard Physical Layer events.

Individual Standard Physical Layer Errors should not be enabled in the

Port {0..17} Error Report Enable

because these occur at a rate consistent with the bit error rate of the lanes associated with

each port, and therefore are part of the normal operation of the system.

PORT_n_ERR_RPT_EN
PORT: 0xP# * 0x40
BCST: 0x03FF04

PORT_n_OPS[PORT_INT_EN]
PORT: 0x P# * 0x100
BCST: 0xF4FF04

PORT_n_OPS[PORT_PW_EN]
PORT: 0x P# * 0x100
BCST: 0xF4FF04

PORT_n_OPS[PORT_LOG_EN]
PORT: 0x P# * 0x100
BCST: 0xF4FF04

Interrupt

Error Logging

PORT_n_ERR_RATE_EN_CSR
PORT: 0x P# * 0x40
BCST: 0xFFFF44

PORT_n_ERR_DET_CSR
PORT: 0x P# * 0x40
BCST: 0xFFFF40

PORT_n_CAPT_0_CSR
0x P# * 0x40

Error Detection

Error Capture

PORT_n_CAPT_1_CSR
0x P# * 0x40

PORT_n_CAPT_2_CSR
0x P# * 0x40

PORT_n_CAPT_3_CSR
0x P# * 0x40

PORT_n_ERR_RATE_CSR
0x P# * 0x40

PORT_n_ERR_RATE_THRESH_CSR
0x P# * 0x40

PORT_n_ATTR_CAPT_CSR[VALID] (!= 0)
0x P# * 0x40

Physical

Layer

Errors

Error Capture
Valid

Interrupts from other

Layers, Functions and Error Logging

> thresh

PORT_n_ERR_STAT_CSR
PORT: 0x P# * 0x20

Physical Layer
Implementation
Specific Errors

PORT_n_ERR_STAT_CSR
[PW_PNDG]
PORT: 0x P# * 0x20

Pending
Port Write

«
...
107
108
109
110
111
...
»

Содержание CPS-1848



































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CPS-1848

Бренд: IBM Страницы: 88

Бренд: wavin Страницы: 4

Бренд: 3Com Страницы: 12

S7906E - Switch

Бренд: 3Com Страницы: 8

SilverStorm 9000

Бренд: Qlogic Страницы: 50

EtherDevice EDS-4009 Series

Бренд: Moxa Technologies Страницы: 18

Бренд: TP-Link Страницы: 2

Бренд: StarTech.com Страницы: 16

Бренд: Black Box Страницы: 10

TGS-1080-M12 Series

Бренд: ORiNG Страницы: 2

Бренд: Grizzly Страницы: 2

ADDERView Secure AVS-4128

Бренд: ADDER Страницы: 24

ISCOM2600G (A) Series

Бренд: Raisecom Страницы: 96

Бренд: Heyer Страницы: 29

ProSafe GSM5212P

Бренд: NETGEAR Страницы: 2

Cross-8/HPoE-10G

Бренд: Evidence Страницы: 321

Бренд: R&S Страницы: 37

Бренд: Black Box Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды