Huvitz HRK-7000 Скачать руководство пользователя

Страница: 29 / 97

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A 29

Measurement

If the following situations happen, contact to the agents of Huvitz after immediately
pushing the power switch off, and pulling the power cord out of AC Power
connection part.

●

In case that smoke comes, or strange smell or sound is heard from the equipment.

●

In case that liquid is poured to the machine, or metallic substance is inputted into

the equipment.

●

In case that the equipment is fallen down, or the exterior case of it is broken

The keys change as follows as pushing FUNC button.

The change of measurement mode is to be set up as shown in the above figure as the

product is wrapped in Huvitz. IOL button is possible to use in K&R measurement mode

and REF measurement mode only. As pushing IOL button, the function of measuring

IOL is to be performed, and the function stops as pushing the button again (refer to the

section 8.6). The refractive power value measured according to the value of VD (Vertex

WARNING

IOL

ILLUM

MODE

FOCUS

AUTO

COMP

SIZE

DISP

Z-MAP

Содержание HRK-7000


































































































Результаты поиска

Содержание HRK-7000

Отзывы:

Похожие инструкции для HRK-7000

Бренды по названию

Популярные бренды

Huvitz HRK-7000, Руководство пользователя

Результаты поиска

Содержание HRK-7000

Отзывы:

Похожие инструкции для HRK-7000

Бренды по названию

Популярные бренды