Huvitz HRK-7000 Скачать руководство пользователя

Страница: 28 / 97

28 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

Measurement

Manual Adjustment

①

Adjust the focus and position of model eye as like in the procedure of

adjusting measurement position & focus explained in the previous page.

②

Push the measurement switch. In case that the measurement is not

performed while the message of TRY AGAIN appears on the upper left

side of the monitor, push the measurement switch again after repeating

the procedure of (a).

③

Check whether diopter value is measured or not. In case that the

measured value is not satisfactory, measure it with the same way and

check it again.

Automatic Adjustment

①

Push

AUTO

button at the bottom of monitor.

②

Adjust the position and focus of model eye as like in like in the procedure

of adjusting measurement position & focus explained in the previous page.

③

It the focus is well adjusted as the bright dot appears inside the internal

array ring and the focus-adjustment circle symbol appears on the bright

dot, then, the measurement starts automatically.

Содержание HRK-7000


































































































Результаты поиска

Содержание HRK-7000

Отзывы:

Похожие инструкции для HRK-7000

Бренды по названию

Популярные бренды

Huvitz HRK-7000, Руководство пользователя

Результаты поиска

Содержание HRK-7000

Отзывы:

Похожие инструкции для HRK-7000

Бренды по названию

Популярные бренды