Huvitz HRK-7000 Скачать руководство пользователя

Страница: 41 / 97

--------------------------------------------------------Auto Ref/Keratometer HRK-7000/7000A 41

8.2.

Keratometry (KER Mode)

It is the mode to measure the corneal curvature solely.

Do not measure the base curve of hard contact lens in this mode. Please refer to

CLBC mode in section 8.5 regarding the base curve of hard contact lens.

Check whether or not the screen of monitor is in measurement mode.

KER Mode Selection

Push MODE button until “KER” is to be indicated on the upper right side of the

screen.

Perform the same 2, 3 procedure of consecutive measurement of refractive power.

8.2.1.

Manual Measurement Mode

①

Perform the adjustment of array and focus as like in the procedure of section 8.1.1.

②

Measurement

Push the measurement button.

The measurement continues to be performed as you keep pushing the

measurement button.

As the measurement is completed, the measured result is to be indicated on the

screen of monitor. In case of the consecutive measurement, the result of

previous measurement is to be indicated.

Содержание HRK-7000


































































































Результаты поиска

Содержание HRK-7000

Отзывы:

Похожие инструкции для HRK-7000

Бренды по названию

Популярные бренды

Huvitz HRK-7000, Руководство пользователя

Результаты поиска

Содержание HRK-7000

Отзывы:

Похожие инструкции для HRK-7000

Бренды по названию

Популярные бренды