Huvitz HRK-7000 Скачать руководство пользователя страница 24

Страница: 24 / 97

24 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

Change to K&R, REF Modes

If “K&R” or “REF” is not indicated on the monitor, push the MODE button

until one of them is to appear.

Adjustment of Position for Measurement & Focus

Tilt the operation lever over the model eye until the bright dots appear

around the internal array ring.

Adjust so that the bright dot shall come inside the array ring while

watching the monitor.

Adjust the focus so that the focus-adjustment circle symbol shall appear

on the bright dot.

Height Adjustment: Adjust it by rotating the operation lever or the chin-rest

height adjustment lever.

Left/Right Adjustment: Adjust so that the bright dot shall come inside the

internal array ring by tilting the operation lever to the directions of left/right.

Focus Adjustment: Adjust the focus so that the focus-adjustment circle

symbol shall appear on the bright dot by tilting the operation lever

forward/backward.

Auto-tracking Function

Press the FOCUS button for Auto-tracking Function.

Perform rough alignment and focusing by manipulating the joystick to place

in the working range of auto-tracking.

When the device is placed within the working ranfe of auto-tracking, it

automatically starts alignment and focusing.

The mark is displayed, when the main body is not within the working

range of auto-tracking.

At that time, manipulrate the joystick or chinrest up/down button in the

direction of the as Figures.

Содержание HRK-7000


































































































Результаты поиска

Содержание HRK-7000

Отзывы:

Бренды по названию

Популярные бренды

Huvitz HRK-7000, Руководство пользователя

Результаты поиска

Содержание HRK-7000

Отзывы:

Бренды по названию

Популярные бренды