Huvitz HRK-7000 Скачать руководство пользователя

Страница: 96 / 97

96 Auto Ref/Keratometer HRK-7000/7000A --------------------------------------------------------

14.

Service Information

If the instrument appears malfunctioning, before calling a customer service, it is

highly recommended to check the instrument according to the troubleshooting

procedure in section 11 of this manual.

If any problem persists or the instrument is damaged or malfunctioning, contact

Huvtiz or local distributor for service with the following information:

Name of the instrument: Auto Ref/Keratometer MRK-3100P

Serial number of the instrument: refer to the 9-digit number on its product

label or name plate

Descriptions of Problem: In detail

Date of Purchase:

Dealer’s Name:

Dealer Address:

Dealer Phone No.:

Model No.:

Serial No.:

(

Huvitz recommends customers to fill up the following form after purchase and retain

this manual as a permanent record of purchase.)

Write us at:

HUVITZ Co., Ltd.

Huvitz B/D, 689-3 Geumjeong-dong

Gunpo-si Gyeonggi-do, South Korea

435-862

Tel

: +82-31-442-8868

Fax

: +82-31-442-8619

URL

http://www.huvitz.com

e-mail: [email protected]

Содержание HRK-7000


































































































Результаты поиска

Содержание HRK-7000

Отзывы:

Похожие инструкции для HRK-7000

Бренды по названию

Популярные бренды

Huvitz HRK-7000, Руководство пользователя

Результаты поиска

Содержание HRK-7000

Отзывы:

Похожие инструкции для HRK-7000

Бренды по названию

Популярные бренды