Hussmann RL2SP Скачать руководство пользователя страница 64

Страница: 64 / 65

P/N 3053328_C 6-5

Reach-In

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

REPAIRING ALUMINUM COIL

The aluminum coils used in Hussmann merchandisers
may be easily repaired in the field. Materials are
available from local refrigeration wholesalers.

Hussmann recommends the following solders and
technique:

Solders

Aladdin Welding Products Inc.

P.O. Box 7188

1300 Burton St.

Grand Rapids, MI 49507

Phone: 1-800-645-3413
Fax: 1-800-645-3414

X-Ergon

1570 E. Northgate

P.O. Box 2102

Irving, TX 75062

Phone: 1-800-527-9916

NOTE:
Hussmann Aluminum melts at

1125°F (607°C)

Aladdin 3-in-1 rod at

732°F (389°C)

X-Ergon Acid core at

455°F (235°C)

Technique:

1. Locate Leak.

2. REMOVE ALL PRESSURE.

3. Brush area UNDER HEAT.

4. Use PRESTOLITE TORCH ONLY.

Number 6 tip.

5. Maintain separate set of stainless steel brushes and

USE ONLY ON ALUMINUM.

6. Tin surface around area.

7. Brush tinned surface UNDER HEAT, thoroughly

filling the open pores around leak.

8. Repair leak. Let aluminum melt solder, NOT the

torch.

9. Don’t repair for looks. Go for thickness.

10. Perform a leak check.

11. Wash with water.

12. Cover with a good flexible sealant.

Содержание RL2SP


































































Результаты поиска

Содержание RL2SP

Отзывы:

Похожие инструкции для RL2SP

Бренды по названию

Популярные бренды

Hussmann RL2SP, Руководство по установке и эксплуатации

Результаты поиска

Содержание RL2SP

Отзывы:

Похожие инструкции для RL2SP

Бренды по названию

Популярные бренды