Hussmann RL2SP Скачать руководство пользователя страница 52

Страница: 52 / 65

P/N 3053328_C 4-3

Reach-In

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

STARTUP AND OPERATION

See the merchandiser’s Technical Data Sheet for

refrigerant settings and defrost require ments. Bring

merchandisers down to the operating temperatures

listed on the data sheet.

Excessive ambient conditions may cause

condensation and therefore sweating of doors.

Facility operators should monitor doors and

floor conditions to ensure safety of persons.

STOCKING

Product should NOT be placed in merchandisers until

all refrigeration controls have been adjusted and

merchandisers are at proper operating temperature.

All shelves and the lower deck are intended to display

product. Shelf height is adjustable in one inch

increments. Spacing of 10 inches is recommended

for most applications. Maximum load per shelf is

200 pounds.

Proper rotation of product during stocking is

necessary to prevent product loss. Always bring the

oldest product to the front and set the newest to the

back.

discharge

and

reTurn

flues

musT

remain

open

and

free

obsTrucTion

all

Times

to provide

proper refrigeration and air curtain performance. Do

not allow product, packages, signs, etc. to block these

grilles. Do not use non-approved shelving, baskets,

display racks, or any accessory that could hamper air

curtain performance.

Do not prop doors open while stocking. And keep

the doors closed as much as possible to prevent coil

frosting and high merchandiser temperature.

LOAD LIMITS

Shelf life of perishables will be short if load limit is

violated.

Time

should

merchandisers

sTocked

beyond

The

load

limiTs

indicaTed

Various shelf depths are offered with Reach In cases.

The standard depth on all Reach-In cases is 22” (21”

on RFLNS and RFMNS cases). Some cases have been

designed to support larger shelves, but require design

modifications to support the extra shelf length. These

cases have a label near the serial plate that reads: This

case has been reinforced to support 26” shelves.

DO NOT INSTALL 26” SHELVES IN ANY REACH

IN CASE THAT DOES NOT HAVE THIS LABEL.

not

block

honeycomb

Hussmann recommends

solid shelves for ice cream.

Do not store items or flammable

materials atop the unit.

Do not walk on case.

RL-W

RL-SP

LOAD

LIMITS

FAN

COIL

Содержание RL2SP


































































Результаты поиска

Содержание RL2SP

Отзывы:

Похожие инструкции для RL2SP

Бренды по названию

Популярные бренды

Hussmann RL2SP, Руководство по установке и эксплуатации

Результаты поиска

Содержание RL2SP

Отзывы:

Похожие инструкции для RL2SP

Бренды по названию

Популярные бренды