Hussmann RL2SP Скачать руководство пользователя страница 5

Страница: 5 / 65

ANSI Z535.5 DEFINITIONS

• DANGER – Indicate[s] a hazardous
situation which, if not avoided, will
result in death or serious injury.

• WARNING – Indicate[s] a hazardous
situation which, if not avoided, could
result in death or serious injury.

• CAUTION – Indicate[s] a hazardous
situation which, if not avoided, could
result in minor or moderate injury.

• NOTICE – Not related to personal injury –
Indicates[s] situations, which if not avoided,
could result in damage to equipment.

REVISION HISTORY

REVISION C — APRIL 2019
1. Added new medium temp. models

REVISION B — FEBRUARY 2019
1. Added new low temp. models; updated

Section 2

REVISION A — MARCH 2018
1. Original Issue

Do NOT remove shipping crate until
the merchandiser is positioned for
installation.

Excessive ambient conditions may
cause condensation and therefore
sweating of doors. Facility operators
should monitor doors and floor
conditions to ensure safety of
persons.

A 4-inch (102 mm) space between

the rear of the merchandiser and wall

must be maintained for air circulation.

However, in high ambient conditions,

sweating may still occur. If this

happens install a method of forced

ventilation such as a fan ventilation kit.

INSTALLATION

TOOL LIST

Unloading From Trailer:

Lever Bar (also known as a Mule,

Johnson Bar, J-bar, Lever Dolly, and

pry lever)

Moving Dolly

Setting Case Line-Up:

Level, 4 ft suggested

Ratchet

in. Socket

Battery Drill/Screw Gun

Caulking Gun

10 in. Adjustable Crescent Wrench

Reach-In

P/N 3053328_C

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Содержание RL2SP


































































Результаты поиска

Содержание RL2SP

Отзывы:

Похожие инструкции для RL2SP

Бренды по названию

Популярные бренды

Hussmann RL2SP, Руководство по установке и эксплуатации

Результаты поиска

Содержание RL2SP

Отзывы:

Похожие инструкции для RL2SP

Бренды по названию

Популярные бренды