Hussmann RL2SP Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 65

background image

2-16

E

lEctrIcal

/ c

ontrollEr

/ W

atEr

/ r

EfrIgEratIon

P/N 3053328_C

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM

REFRIGERATION

Each self-contained case is equipped with its own
condensing unit(s), one for every 2 or 3-door. The
refrigeration system is factory charged and sealed.
Each case has one electronic controller. Thus, a
2-door case has one condensing unit, a 4-door case has
two condensing units.

Self contained merchandisers use R-290 (propane),
refrigerant. All models have compressor(s). The
systems employ capillary tubes for refrigerant flow
control. If the capillary tube becomes plugged or
damaged, replace the entire capillary tube. Refer
to the case serial plate for refrigerant charge
information. The following illustration shows the
details of the refrigeration system.

CONDENSING UNIT ACCESS

Condensing units are located on top of the case. The
condensing unit(s) have an electrical box for wire
connections and field service. All the cases and condensing
units’ electrical connections are done at the factory.

Risk of fire or explosion. R-290 (propane) refrigerant is

flammable, and the refrigeration system should be serviced or

repaired only by trained service personnel. Do NOT puncture

refrigerant tubing.

Attention trained service personnel:

Mandatory safety service procedures

must be followed when servicing

refrigeration system.

Opening condensing unit electrical

box exposes personnel to electrical

hazard and should only be preformed

by a qualified service technician.

2-8

Electrical Box

with

Disconnect Switch

Water Inlet

Water Outlet

Condensing Unit

Enclosure

Condensing Unit
Enclosure

Water Inlet

Water Outlet

Electrical Box
with Disconnect
Switch

«
...
37
38
39
40
41
...
»

Содержание RL2SP


































































Отзывы:

Нет отзывов

Похожие инструкции для RL2SP

Бренд: APW Wyott Страницы: 20

Бренд: Hussmann Страницы: 6

Бренд: Hussmann Страницы: 15

Бренд: Alto-Shaam Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды