Hussmann RL2SP Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 65

background image

Installation &

Operation Manual

Shipped With Case Data Sheets

P/N 3053328_C

April 2019

Spanish P/N 3053329

French P/N 3053330

Micro-Distributed

Reach-In Merchandisers

with

R-290 (Propane)

Refrigerant

IMPORTANT!

Keep in store for

future reference!

WARNINGS:

If the information in these instructions are not
followed exactly, a ﬁre or explosion may result, causing
property damage, personal injury or death.

Installation and service must be performed by a qualiﬁed
installer or service agency.

READ THE ENTIRE MANUAL BEFORE
INSTALLING OR USING THIS
EQUIPMENT.

The unit uses R-290 (propane) gas as the refrigerant.
R-290 (propane) is ﬂammable and heavier than air.
It collects ﬁrst in low areas but can be circulated by
the fans. If  propane gas is present or even suspected,
do not allow untrained personnel to attempt to ﬁnd
the cause. The propane gas used in the unit has no
odor. The lack of  smell does not indicate a lack of
escaped gas. If  a leak is detected, immediately evacuate
all persons from the store, and contact the local ﬁre
department to advise them that a propane leak has
occurred. Do not let any persons back into the store
until the qualiﬁed service technician has arrived and
that technician advises that it is safe to return to the
store. No open ﬂames, cigarettes or other possible
sources of  ignition should be used inside or in the
vicinity of  the units.

FAILURE TO ABIDE BY THIS WARNING COULD
RESULT IN AN EXPLOSION, DEATH, INJURY
AND PROPERTY DAMAGE.

MANUAL - MDS LOW TEMP IO

TITLE PAGE

2-1

Disconnect

Switch

Use this manual along with door manual

P/N 0425683 for cases with Innovator Doors

UL

US

C

LISTED

This manual applies to the
following case models:

RL2W - RL5W
RLN2W - RLN5W
RLNI4W - RLNI5W
RL2SP - RL5SP
RLN2SP - RLN5SP
RLNI5SP - RLNI5SP
RM2W - RM5W
RMN2W - RMN5W

For clarity in the documentation, all illustrations use the

RL, RLN, and RLNI nommenclatures for reference.

1
2
3
...
»

Содержание RL2SP


































































Отзывы:

Нет отзывов

Похожие инструкции для RL2SP

Бренд: lancer Страницы: 10

Бренд: Randell Страницы: 2

Бренд: Bakers Pride Страницы: 2

Бренд: Hussmann Страницы: 6

PREMIUM MD 100-3

Бренд: Fri-Jado Страницы: 36

HOT DELI Two Tier 3

Бренд: Fri-Jado Страницы: 38

COLD DELI CD 3 Self

Бренд: Fri-Jado Страницы: 68

Бренд: Fri-Jado Страницы: 124

TYLER Advantage NLBN

Бренд: Carrier Страницы: 27

Бренд: Carrier Страницы: 41

Бренд: Costan Страницы: 140

Бренд: Costan Страницы: 149

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды