Husqvarna FE 450 Скачать руководство пользователя страница 50

Страница: 50 / 128

12 SERVICE WORK ON THE CHASSIS

F00277-10

Main work

–

Open the cable holder in front of the right radiator and detach the wiring harness.

–

Remove screws



and hang the voltage regulator to the side.

–

Open the cable holder in front of the left radiator and detach the wiring harness.

F00279-10

–

Remove screw



–

Remove screw



–

Take off the upper triple clamp with the handlebar and set it aside.

Info

Cover the components to protect them against damage.
Do not kink the cables and lines.

F00278-10

–

Remove O-ring



and protective ring



–

Take off the lower triple clamp with the steering stem.

–

Remove the upper steering head bearing.

12.10

Installing the lower triple clamp

B01632-10

Main work

–

Clean the bearing and sealing elements, check for damage, and grease.

High viscosity grease (

p. 118)

–

Position the lower triple clamp with the steering stem. Mount the upper steering

head bearing.

–

Check whether upper steering head seal



is correctly positioned.

–

Mount protective ring



and O-ring



F00279-11

–

Position the upper triple clamp with the handlebar.

–

Mount screw



but do not tighten yet.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды