Husqvarna FE 450 Скачать руководство пользователя страница 121

Страница: 121 / 128

25 STANDARDS

119

JASO T903 MA

Different technical development directions required a new specification for 4-stroke motorcycles

–

the JASO T903 MA Standard.

Earlier, engine oils from the automobile industry were used for 4-stroke motorcycles because there was no separate motorcycle

specification. Whereas long service intervals are demanded for automobile engines, high performance at high engine speeds are

in the foreground for motorcycle engines. In most motorcycles, the gearbox and the clutch are lubricated with the same oil as the

engine. The JASO MA Standard meets these special requirements.

SAE

The SAE viscosity classes were defined by the Society of Automotive Engineers and are used for classifying oils according to their

viscosity. The viscosity describes only one property of oil and says nothing about quality.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды