Husqvarna FE 450 Скачать руководство пользователя страница 44

Страница: 44 / 128

11 TUNING THE CHASSIS

F00351-10

–

Turn white adjusting screw



clockwise as far as it will go.

Info

Adjusting screw



is located at the upper end of the left fork leg.

The compression damping is located in left fork leg

COM

(white adjusting

screw). The rebound damping is located in right fork leg

REB

(red adjust-

ing screw).

–

Turn counterclockwise by the number of clicks corresponding to the fork type.
Guideline

Compression damping

Comfort

18 clicks

Standard

15 clicks

Sport

12 clicks

Info

Turn clockwise to increase damping; turn counterclockwise to reduce

damping.

11.13

Adjusting the rebound damping of the fork

Info

The hydraulic rebound damping determines the fork suspension behavior.

F00352-10

–

Turn red adjusting screw



clockwise as far as it will go.

Info

Adjusting screw



is located at the upper end of the right fork leg.

The rebound damping is located in right fork leg

REB

(red adjusting

screw). The compression damping is located in left fork leg

COM

(white

adjusting screw).

–

Turn counterclockwise by the number of clicks corresponding to the fork type.
Guideline

Rebound damping

Comfort

18 clicks

Standard

15 clicks

Sport

12 clicks

Info

Turn clockwise to increase damping; turn counterclockwise to reduce

damping.

11.14

Adjusting the spring preload of the fork

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 45)

F00353-10

Main work

–

Turn the adjusting wings



counterclockwise all the way.

The marking

aligns with the right wing.

Info

Make the adjustment by hand only. Do not use a tool.
Make the same adjustment on both fork legs.

–

Turn the adjusting wings clockwise.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды