Husqvarna FE 450 Скачать руководство пользователя страница 69

Страница: 69 / 128

12 SERVICE WORK ON THE CHASSIS

12.39

Checking the swingarm

401520-01

–

Check the swingarm for damage, cracking, and deformation.
» If the swingarm shows signs of damage, cracking, or deformation:

–

Change the swingarm.

Info

Always change a damaged swingarm. Repair of the swingarm is

not authorized by Husqvarna Motorcycles.

12.40

Checking throttle cable routing

Preparatory work

–

Remove the air filter box cover. (

p. 56)

–

Remove the seat. (

p. 55)

–

Remove the fuel tank.

(

p. 60)

F00455-01

Main work

–

Check throttle cable routing.

Both throttle cables must be routed, side by side, on the back of the handle-

bars and above the fuel tank bracket, to the throttle valve body. Both throttle

cables must be secured behind the fuel tank contact area rubber band.

» If the throttle cable routing is not as specified:

–

Correct throttle cable routing.

Finishing work

–

Install the fuel tank.

(

p. 61)

–

Mount the seat. (

p. 55)

–

Install the air filter box cover. (

p. 56)

12.41

Checking the rubber grip

401197-01

–

Check the rubber grips on the handlebar for damage, wear, and looseness.

Info

The rubber grips are vulcanized onto a sleeve on the left and onto the han-

dle tube of the throttle grip on the right. The left sleeve is clamped onto the

handlebar.
The rubber grip can only be replaced with the sleeve or the throttle tube.

» If a rubber grip is damaged, worn, or loose:

–

Change the rubber grip.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды