Husqvarna FE 450 Скачать руководство пользователя страница 62

Страница: 62 / 128

12 SERVICE WORK ON THE CHASSIS

M00435-10

Main work

–

Remove all screws on the main silencer.

–

Take off silencer cap



and O-ring



–

Take off outer tube



and O-ring



–

Remove glass fiber yarn filling



from inner tube



–

Clean the parts that need to be reinstalled and check for damage.

–

Fit the new glass fiber yarn filling onto the inner tube.

–

Mount O-ring



onto connecting cap



–

Position the inner tube with the connecting cap and glass fiber yarn filling in the

outer tube.

–

Mount O-ring



on the silencer cap.

–

Position the silencer cap with O-ring



in the outer tube.

–

Mount and tighten all of the screws.
Guideline

Screws on the main silencer

7 Nm (5.2 lbf ft)

Finishing work

–

Install the main silencer. (

p. 59)

–

Install the right side cover. (

p. 58)

12.31

Removing the fuel tank

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Preparatory work

–

Remove the air filter box cover. (

p. 56)

–

Remove the seat. (

p. 55)

K00596-10

Main work

–

Unplug connector



of the fuel pump.

–

Clean plug-in connection



of the fuel line thoroughly with compressed air.

Info

Under no circumstances should dirt enter into the fuel line. Dirt in the fuel

line clogs the injection valve!

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды