Husqvarna FE 450 Скачать руководство пользователя страница 21

Страница: 21 / 128

CONTROLS

6.18

Side stand

401943-10

The side stand



is attached to the left side of the vehicle.

401944-10

The side stand is used for parking the motorcycle.

Info

When you are riding, side stand



must be folded up and secured with rub-

ber band



6.19

Steering lock

F00268-10

Steering lock



is fitted on the left side of the steering head.

The steering lock is used to lock the steering. Steering, and therefore riding, is no

longer possible.

6.20

Locking the steering

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

400732-01

–

Park the vehicle.

–

Turn the handlebar as far as possible to the right.

–

Grease the steering lock regularly.

Universal oil spray (

p. 118)

–

Insert the key in the steering lock (

p. 19), turn it to the left, press it in, and turn

it to the right. Remove the key.

Steering is no longer possible.

Info

Never leave the key in the steering lock.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды