Husqvarna FE 450 Скачать руководство пользователя страница 24

Страница: 24 / 128

SPEEDOMETER

401912-01

–

Wait for 5 seconds.

The speedometer changes to the next menu item. The

symbol flashes.

Resetting the time

–

Press the left button.

The value decreases.

Advancing the time

–

Press the right button.

The value increases.

401913-01

–

Wait for 5 seconds.

The speedometer changes to the next menu item. The

symbol flashes.

–

Set the service.
Guideline

One-time service after

1 h

Service every

15 h

Shortening the service interval

–

Press the left button.

The value decreases.

Extending the service interval

–

Press the right button.

The value increases.

401914-01

Switching off the service interval display

–

Press and hold the left button.

off

appears on the display.

7.5

Setting the kilometers or miles

Info

If the unit is changed, the value

ODO

is retained and converted accordingly.

Condition

The motorcycle is stationary.

401909-01

–

Press both buttons for 3

–

5 seconds.

The Setup menu is displayed. The

UNIT

display flashes.

–

Press one of the buttons to select

UNIT

for the speed in kilometers

KM/H

miles

M/H

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды