Husqvarna FE 450 Скачать руководство пользователя страница 61

Страница: 61 / 128

12 SERVICE WORK ON THE CHASSIS

12.28

Removing the main silencer

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down before performing any work on the vehicle.

Preparatory work

–

Remove the right side cover. (

p. 58)

K00594-10

Main work

–

Disconnect spring



Spring hook (50305017000)

–

Remove screws



and take off the main silencer.

12.29

Installing the main silencer

K00595-10

Main work

–

Position the main silencer. Mount screws



but do not tighten yet.

–

Attach spring



Spring hook (50305017000)

–

Tighten screws



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

Finishing work

–

Install the right side cover. (

p. 58)

12.30

Changing the glass fiber yarn filling in the main silencer

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down before performing any work on the vehicle.

Info

Over time, the fibers of the glass fiber yarn escape and the damper "burns" out.
Not only is the noise level higher, the performance characteristic changes.

Preparatory work

–

Remove the right side cover. (

p. 58)

–

Remove the main silencer. (

p. 59)

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды