Husqvarna FE 450 Скачать руководство пользователя страница 84

Страница: 84 / 128

14 WHEELS, TIRES

14.4

Installing the rear wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

H00937-10

Main work

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change the rear wheel bearing.

–

Clean and grease shaft seal rings



and contact surface



of the spacers.

Long-life grease (

p. 118)

–

Insert the spacers.

F00356-10

–

Position the rear wheel and insert wheel spindle



–

Mount the chain.

The brake linings are correctly positioned.

F00321-11

–

Position chain adjuster



. Mount nut



, but do not tighten it yet.

–

Make sure that chain adjusters



are fitted correctly on adjusting screws



–

Check the chain tension. (

p. 63)

–

Tighten nut



Guideline

Nut, rear wheel spindle

M20x1.5

80 Nm (59 lbf ft)

Info

The wide adjustment range of the chain adjusters (32 mm (1.26 in))

enables different secondary ratios with the same chain length.
Chain adjusters



can be turned by 180°.

–

Operate the foot brake lever repeatedly until the brake linings are in contact with

the brake disc and there is a pressure point.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 45)

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды