Humminbird MEGA Live Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 75

background image

52

Control Head Setup

4. Pair the TargetLock Heading Sensor to the Control Head

Use the following instructions to pair the MEGA Live Imaging TargetLock Heading
Sensor to your Humminbird control head.

APEX/SOLIX Series

1. Press the HOME key.

2. Select Settings > CHIRP Sonar > Pair TargetLock Heading Sensor.

3. On your TargetLock Heading Sensor, press the Pair button.

4. The control head and the TargetLock Heading Sensor will go into Pairing Mode.

If 30 seconds pass while in Pairing Mode and they do not successfully pair, an
error message will display signaling that the pairing has timed out. Repeat the
procedure.

NOTE:

You can check the MEGA Live Device List to confirm that the TargetLock

Heading Sensor is paired. Select Home > Settings > CHIRP Sonar > Device List.

HELIX Series

1.

Main Menu:

On your control head, press the MENU key twice.

2. Select the Accessories tab > MEGA Live > MEGA Live Installation.

3. Select Pair TL Heading Sensor, and press the RIGHT Cursor key.

4. On your TargetLock Heading Sensor, press the Pair button.

5. The control head and the TargetLock Heading Sensor will go into Pairing Mode.

If 30 seconds pass while in Pairing Mode and they do not successfully pair, an
error message will display signaling that the pairing has timed out. Repeat the
procedure.

NOTE:

You can check the MEGA Live Device List to confirm that the TargetLock

Heading Sensor is paired. Press the MENU key twice to open the Main Menu.
Select the Accessories tab > MEGA Live > Device List.

«
...
56
57
58
59
60
...
»

Содержание MEGA Live












































































Отзывы:

Нет отзывов

Похожие инструкции для MEGA Live

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: Gardigo Страницы: 32

Бренд: Magma Страницы: 16

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

Бренд: Teac Страницы: 76

Бренд: Teac Страницы: 3

Бренд: Teac Страницы: 50

Бренд: Teagle Страницы: 2

Бренд: H&S Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды