Humminbird MEGA Live Скачать руководство пользователя страница 49

Страница: 49 / 75

Control Head Setup

Set Up the Control Head

Use the following instructions to power on the control head and confirm the MEGA Live
Imaging transducer and the Humminbird GPS Heading Sensor (optional) are detected
by the unit (for Minn Kota Heading Sensor instructions, see your

i-Pilot Link Owner’s

Manual

CAUTION!

It is important to finish all installation connections before powering on the

control head. It may take up to a minute for the MEGA Live Imaging transducer and other
attached equipment to be detected by the control head.

NOTE:

For MEGA 360 set up instructions, see the manual that was included with your

transducer or visit our Web site at

humminbird.com

1. Confirm Connections

APEX/SOLIX Series

1. Turn on the power source from the main switch.

2. On the control head, press and hold the POWER key.

If you are powering on

a control head in a multiple-control head Ethernet network

, make sure your

ethernet switch(es) have power and your MEGA Live TargetLock is connected to
the switch.

3. Select Normal mode.

4. Review the status bar in the top, right corner of the screen to confirm the sensor status

for the MEGA Live Imaging transducer and the GPS Heading Sensor is connected.

MEGA Live Status Icon

Icon Description

Connected/In Water/Pinging:

The MEGA Live is

connected, in the water, and pinging.

Connected/In Water/Not Pinging:

The MEGA Live

is connected and in the water, but it is not pinging.

Connected/Out of Water:

The MEGA Live is

connected, but the wet indicator is out of the water.

Connection Lost:

The connection to the MEGA

Live was lost.

Содержание MEGA Live












































































Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды

Humminbird MEGA Live, Руководство пользователя

Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды