Humminbird MEGA Live Скачать руководство пользователя страница 63

Страница: 63 / 75

Control Head Setup

Confirming the Heading Digital Readout (APEX/SOLIX)

heading

(heading

sensor

required)

course

HELIX Series

Main Menu:

Press the MENU key twice.

2. Select the Chart tab > North Reference > Magnetic.

3. Press the EXIT key.

4. Select the Setup tab > Select Readouts (G3N models) or Edit Data Boxes (G4N

models).

NOTE:

If the Select Readouts or Edit Data Boxes menu option does not appear

under the Setup tab, change the User Mode to Custom. Select Main Menu
> Setup tab > User Mode > Custom.

5. Select a Readout position or Data Box position and use the RIGHT or LEFT Cursor

keys to select Vessel. Then select Heading. Select another Readout position or
Data Box and select Course Over Ground.

6. Press the EXIT key until the Main Menu is closed.

7. Press and hold the VIEW key. Select Chart > Chart View.

8. Navigate the boat in a straight line, in calm, open water at 4.5 mph. Compare

the Heading digital readout on the screen with the Course (COG) digital readout.
The readouts should be within approximately 5° of each other.

Содержание MEGA Live












































































Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды

Humminbird MEGA Live, Руководство пользователя

Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды