Humminbird MEGA Live Скачать руководство пользователя страница 11

Страница: 11 / 75

Update Software

Update Accessory Software with an SD Card

You will need an SD or microSD card (depending on your control head model).

1. Install a formatted SD or microSD card into the computer card slot.

2. Go to

humminbird.com

, and click Support > Software Updates.

3. Scroll down to Accessories and Mapping. The available software updates are

listed as downloads under each accessory product. Confirm your control head
model is listed in the software description.

• Read the notices and instructions, and select Download.

• Follow the on-screen prompts to save the software file to the SD or microSD

card.

4. Insert the SD or microSD card (with the software file) into the control head

card slot.

5. Power on your Humminbird control head. Start

Normal

mode.

APEX/SOLIX:

Select the Files tool. From the Software Update tab, scroll to

MEGA Live on the Accessories list. Confirm that the most current software
version is selected from the list, and select Install Now.

HELIX:

The software will be automatically detected. It may take up to two

minutes for the software to be detected on the network, and the control head
will display a dialog box to indicate that the update is in progress.

7. When the software update is complete, remove the SD or microSD card from

the control head card slot.

Restart:

If you don’t have any other software updates to install, power off the

control head, and restart it.

Содержание MEGA Live












































































Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды

Humminbird MEGA Live, Руководство пользователя

Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды