Humminbird MEGA Live Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 75

background image

1

Introduction

Introduction

This manual will guide you through the following installation requirements for the
MEGA Live Imaging TargetLock transducer:

• Installing the Transducer and Foot Pedal

• Connecting to the Control Head and Power

• Testing the Installation

• Powering Off

Before proceeding with this installation, the Humminbird control head
and Minn Kota® Ultrex trolling motor should be installed. The MEGA Live
Imaging transducer can be connected directly to the control head or to
a Humminbird Ethernet Switch (optional, separate purchase required)
for networking. See the Ethernet Switch installation instructions to
install the Ethernet Switch.

Compatibility

Control Heads:

MEGA Live Imaging TargetLock is compatible with all APEX™ Series

and SOLIX® Series fish finders, HELIX® Series G3N and G4N fish finders equipped
with MEGA , and HELIX 7 G4N fish finders with MEGA Down Imaging or
MEGA Side Imaging. It can be mounted on Minn Kota Ultrex trolling motors.

Minn Kota Trolling Motor

Humminbird Fish Finder

Minn Kota Ultrex

APEX Series:

All models

SOLIX Series:

All models

HELIX Series:

HELIX G3N and G4N models

with MEGA and HELIX 7 G4N
models with MDI or MSI

«
...
5
6
7
8
9
...
»

Содержание MEGA Live












































































Отзывы:

Нет отзывов

Похожие инструкции для MEGA Live

Бренд: Raymarine Страницы: 90

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: XM Fitness Страницы: 10

Бренд: NatureZap Страницы: 2

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: Ultrawave Страницы: 30

Бренд: Ultrasound Technologies Страницы: 12

Бренд: Valcom Страницы: 6

Бренд: Vaisala Страницы: 60

Бренд: EuroLite Страницы: 2

Бренд: U-Line Страницы: 6

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Turbo Jet 10 i-CON

Бренд: Stocks AG Страницы: 30

Randell DROP-IN 9550-290

Бренд: Unified Brands Страницы: 16

Бренд: E-LINK Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды