Humminbird MEGA Live Скачать руководство пользователя страница 50

Страница: 50 / 75

Control Head Setup

GPS Heading Sensor Icon

Icon Description

Compass:

The selected heading sensor is on and

heading data is being received.

GPS

Detected and Active:

The GPS receiver is detected

and a GPS fix has been obtained.

GPS

Connected but not Detected or Active:

The GPS

receiver is connected, but not detected on the
network or no GPS fix has been obtained.

GPS

Connected but not Transmitting/Receiving:

The

GPS receiver is detected, but it doesn’t have a GPS fix.

NOTE:

For additional system status, select Home > Settings > Network >

Network Info.

MEGA Live Imaging Transducer Connected (APEX/SOLIX)

MEGA Live

Imaging listed

MEGA Live icon

on the status bar

MEGA Live

Imaging

TargetLock

Controller listed

Содержание MEGA Live












































































Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды

Humminbird MEGA Live, Руководство пользователя

Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды