Humminbird MEGA Live Скачать руководство пользователя страница 51

Страница: 51 / 75

Control Head Setup

GPS

HELIX Series

1. Turn on the power source from the main switch.

2. On the control head, press and hold the POWER key.

If you are powering on

a control head in a multiple-control head Ethernet network

, make sure your

ethernet switch(es) have power and your MEGA Live TargetLock is connected to
the switch.

3. When the Title screen is displayed, press the MENU key.

4. Select Normal. Press the RIGHT Cursor key.

5. Press and hold the VIEW key. Select System > Accessory Test. Confirm

that

MEGA Live

MEGA Live TL

and

GPS + Heading Sensor

are listed as

Connected. It will take up to two minutes for the equipment to be detected.

6. Press and hold the VIEW key. Select System > GPS Diagnostic View. Confirm

that External GPS is displayed and the Fix Type indicates Enhanced or 3D.

NOTE:

If the GPS Diagnostic View or Accessory Test is not displayed in the

View Rotation, press the MENU key twice to open the Main Menu. Select the
Views tab > GPS Diagnostic View or Accessory Test. Change the setting for each
view to Visible.

HELIX Accessory Test

MEGA Live
and MEGA
Live TL listed
as Connected

GPS Heading
Sensor listed
as Connected

Содержание MEGA Live












































































Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды

Humminbird MEGA Live, Руководство пользователя

Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды