Humminbird MEGA Live Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 75

background image

47

Control Head Setup

2. Select the Network tab > Network Source Setup. Press the RIGHT Cursor key.

3. Select the Live tab from the Network Source Setup dialog box.

4. Select MEGA Live from the transducer list. Press the RIGHT Cursor key. A

checkmark will display in the box to show it is selected.

5. Press the EXIT key until the dialog box is closed.

Selecting the MEGA Live Imaging Transducer

3. Test MEGA Live Imaging on the Control Head

It is important to confirm that the MEGA Live Imaging transducer is providing sonar
returns to the display. The instructions in this section should be performed at trolling
speeds in calm, open water, in a large area that is far from shallow water, boats, or
other obstacles.

APEX/SOLIX Series

1. Tap the View widget icon in the side bar.

NOTE:

Once the MEGA Live has been detected the first time, the MEGA Live

Imaging view will display on the Favorite Views widget.

2. Tap MEGA Live Imaging.

3. The sonar returns from the MEGA Live will begin to display on the MEGA Live

View. Review the display for the following information and see the illustrations

Reviewing the MEGA Live View

.

•

Bottom:

Confirm that the bottom is visible on-screen.

«
...
51
52
53
54
55
...
»

Содержание MEGA Live












































































Отзывы:

Нет отзывов

Похожие инструкции для MEGA Live

Бренд: YSI Страницы: 70

Бренд: jcb Страницы: 41

Бренд: jcb Страницы: 41

Бренд: Icom Страницы: 27

Бренд: Icom Страницы: 72

Бренд: Land Pride Страницы: 36

Skid Steer Rakes SR2672

Бренд: Land Pride Страницы: 2

Бренд: Land Pride Страницы: 2

Disc Harrows DH3510

Бренд: Land Pride Страницы: 2

Бренд: Land Pride Страницы: 4

Бренд: Land Pride Страницы: 4

Straw Crimper CR2572

Бренд: Land Pride Страницы: 16

Бренд: Oakworks Medical Страницы: 28

Бренд: Gardena Страницы: 33

Бренд: A.HABERKORN Страницы: 28

Бренд: Marcy Страницы: 9

RGB-BNTv2 NTV-KIT903

Бренд: Nav TV Страницы: 6

Бренд: Yuwell Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды