Humminbird MEGA Live Скачать руководство пользователя страница 46

Страница: 46 / 75

Cable Installation

3. Route the MEGA 360 Cables

(separate purchase)

1. Connect the power cable to the power cable connector on the pod shaft, and

connect the transducer cable to the transducer cable connector on the pod
shaft.

The connectors are keyed to prevent reversed installation, so be careful not to
force the connectors. Hand-tighten the screw nuts on each connector.

NOTE:

If you are connecting the MEGA 360 Imaging transducer and

another compatible transducer to the same control head, you will need to
purchase a transducer splitter cable (y-cable). See

Compatibility

for the list

of cables, and visit our Web site at

www.humminbird.com/support/

installation-diagrams

to view the wiring diagrams.

2. Route the cables to the side of the trolling motor, over the bow, to the chosen

connection locations in

Section 1: Prepare for Installation

. Leave sufficient

slack in the cables to allow for full movement of the trolling motor during
normal operation.

APEX/SOLIX:

Insert the other end of the

transducer cable to the sonar port on the control
head. Hand-tighten the screw nut.

HELIX:

Insert the transducer adapter cable to the

transducer port on the HELIX control head.

HELIX G3N 8, 9, 10, 12 Cable Tray

Ethernet

temp/speed

power

COM (communications)

transducer

APEX/SOLIX Sonar Port

Содержание MEGA Live












































































Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды

Humminbird MEGA Live, Руководство пользователя

Результаты поиска

Содержание MEGA Live

Отзывы:

Похожие инструкции для MEGA Live

Бренды по названию

Популярные бренды