Huawei UPS2000-G-3 kVA Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 90

background image

UPS2000-G-3 kVA
User Manual (CTC)

3 Installation

Issue 02 (2019-05-05)

Copyright © Huawei Technologies Co., Ltd.

21

If customers purchase input and output power cables by themselves, use the cables that comply with
standards proposed by Underwriters Laboratories (UL) or International Electrotechnical Commission
(IEC).

3.1.4 Unpacking and Checking

shows the transportation safety requirements.

Figure 3-2

Transportation safety requirements



Only trained personnel are allowed to move the UPS.



Do not move the UPS by holding its mounting ears, front panel, terminal cover, or
monitoring module.



At least two persons are required to move the battery pack and transformer because they
are heavy. Exercise caution when moving them. Prevent the battery pack from falling over;
otherwise, fire accidents may occur. Remove rings, watches, and other metal objects when
you move the battery pack.



To prevent shocks or falls, move the UPS gently. After placing the UPS in the installation
position, unpack it carefully to prevent scratches.

Procedure

Step 1

Visually inspect the UPS appearance for shipping damage. If any shipping damage is found,
report it to the carrier immediately.

Step 2

Move the UPS to the installation position.

Step 3

Unpack the case.

Step 4

Check the UPS packing.

1.

Check the UPS bar code (which is at the rear panel of the UPS, near the air exhaust vent),
and ensure that it complies with the order.

2.

If there is any discrepancy, contact your local Huawei office immediately.

----End

3.2 Installation Procedure

For details, see the

UPS2000-G-3 kVA Quick Guide (CTC)

.

«
...
25
26
27
28
29
...
»

Содержание UPS2000-G-3 kVA



























































































Отзывы:

Нет отзывов

Похожие инструкции для UPS2000-G-3 kVA

Бренд: Proseries Страницы: 10

Бренд: Quick Charge Страницы: 4

Бренд: PulseTec Страницы: 24

Бренд: Würth Страницы: 77

Бренд: Radio Shack Страницы: 4

PowerArc ArcField PF2009

Бренд: Spigen Страницы: 17

Бренд: R&S Страницы: 20

Бренд: Champion Страницы: 20

Бренд: GreenWorks Pro Страницы: 36

Бренд: LG Страницы: 52

Бренд: LG Страницы: 38

Бренд: LG Страницы: 57

Бренд: LG Страницы: 68

Бренд: LG Страницы: 82

Бренд: LG Страницы: 106

Бренд: LG Страницы: 150

Бренд: LG Страницы: 176

Бренд: LG Страницы: 336

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды