Huawei UPS2000-G-3 kVA Скачать руководство пользователя страница 21

Страница: 21 / 90

UPS2000-G-3 kVA
User Manual (CTC)

2 Quick Introduction

Issue 02 (2019-05-05)

Rectifier

Figure 2-6

Rectifier in the PDU

(1) Power indicator

(2) Alarm indicator

(3) Fault indicator

(4) Locking latch

(5) Handle

Table 2-6

Indicator description

Indicator

Color

Status

Description

Power indicator

Green

Steady on

The rectifier has an AC power input.

Off

The rectifier has no AC power input.

The rectifier is faulty.

Blinking at
0.5 Hz

The rectifier is being queried.

Blinking at 4
Hz

The rectifier is loading an application program.

Alarm indicator

Yellow

Steady on



The rectifier generates an alarm for power limiting due to
ambient overtemperature.



The rectifier generates an alarm for shutdown due to ambient
overtemperature or undertemperature.



The rectifier shuts down due to overcharge.



The rectifier shuts down due to system current limiting.

The rectifier protects against AC input overvoltage or
undervoltage.

The rectifier is hibernating.

Off

No alarm is generated.

Blinking at
0.5 Hz

The communication between the rectifier and the external
equipment is interrupted.

Fault indicator

Red

Steady on

The rectifier locks out due to output overvoltage.

The rectifier has no output due to an internal fault.

Содержание UPS2000-G-3 kVA



























































































Результаты поиска

Содержание UPS2000-G-3 kVA

Отзывы:

Бренды по названию

Популярные бренды

Huawei UPS2000-G-3 kVA, Руководство пользователя

Результаты поиска

Содержание UPS2000-G-3 kVA

Отзывы:

Бренды по названию

Популярные бренды