Huawei UPS2000-G-3 kVA Скачать руководство пользователя страница 87

Страница: 87 / 90

UPS2000-G-3 kVA
User Manual (CTC)

A Alarm Handling

Issue 02 (2019-05-05)

Alarm
ID
(Alarm
ID-Alar
m
Cause)

Alarm
Name

Alarm
Level

Alarm
Clear
Mode

Impact on the System

Repair Proposal

and humidity
transducer.

0136-01

Faulty
temperat
ure and
humidity
module

Minor

Possible causes: The
temperature and humidity
module is faulty.

Measures:



Check parameter
settings of the
temperature and
humidity transducer.



Replace the temperature
and humidity
transducer.

0158-01

On
bypass

Minor

Automatic
clear

If the bypass is abnormal, the
UPS may power off.

Possible causes:



The inverter is not
started.



The load exceeds the
rated inverter loading
capacity.



The inverter is faulty.

Measures:



Check whether other
alarms are generated. If
yes, see the other
handling methods.



If no, start the UPS
manually.

0159-01

On
battery

Minor

Automatic
clear

The UPS may power off if
batteries are abnormal.

Possible causes:



The mains input is
abnormal.



The UPS is in battery
self-check state.



The mains loading
capability is
insufficient.

Measures:



Check the mains input.
If the mains input is
abnormal, wait until the
mains input recovers.



Check whether the UPS

Содержание UPS2000-G-3 kVA



























































































Результаты поиска

Содержание UPS2000-G-3 kVA

Отзывы:

Huawei UPS2000-G-3 kVA, Руководство пользователя, Страница: 87 / 90

Результаты поиска

Содержание UPS2000-G-3 kVA

Отзывы: