Huawei UPS2000-G-3 kVA Скачать руководство пользователя страница 20

Страница: 20 / 90

UPS2000-G-3 kVA
User Manual (CTC)

2 Quick Introduction

Issue 02 (2019-05-05)

Silk
Screen

Definition

Description

Alarm Status

overvoltage lockout, discharge overcurrent lockout,
discharge overcurrent protection, and cell 1–

fault alarm

DO2

Overload warning,
overdischarge
protection,
overdischarge

If the ESM raises one of the following alarms, the dry
contact supplies an alarm signal:

Discharge undervoltage alarm, discharge undervoltage
protection, discharge due to single-ESM cell low voltage
disconnection, and heavy load warning

Table 2-5

Indicator description

Silk
Screen

Indicator

Color Status

Description

RUN

Running
indicator

Green

Steady on

Communication is normal (including board startup,
self-check, software loading, and board power-on when
not loaded; excluding sleep when the power port or PWR
port is energized).

Off

The ESM is in sleep mode.

Blinking at
0.5 Hz

The LCD user interface (LUI) is querying data.

Blinking at
4 Hz

Communication is disconnected.

ALM

Fault indicator

Red

Steady on

There is a fault or major alarm.

Off

There is no fault or major alarm.

CHG

Charge
indicator

Green

Steady on

The ESM is being charged.

Off

The ESM is open-circuited or discharging.

DCHG

Discharge
indicator

Green

Steady on

The ESM is discharging.

Off

The ESM is open-circuited or being charged.

NOTE



Major alarm: The ESM needs to be maintained immediately.



Minor alarm: The ESM does not require maintenance, but sends a reminder to remote maintenance personnel.



Blinking at long intervals: on for 1s and then off for 1s



Blinking at short intervals: on for 0.125s and then off for 0.125s



All indicators are blinking: The ESM has entered the maintenance mode.



When the ESM is in sleep mode, the fault indicator is off except for reverse-connection protection.

Содержание UPS2000-G-3 kVA



























































































Результаты поиска

Содержание UPS2000-G-3 kVA

Отзывы:

Бренды по названию

Популярные бренды

Huawei UPS2000-G-3 kVA, Руководство пользователя

Результаты поиска

Содержание UPS2000-G-3 kVA

Отзывы:

Бренды по названию

Популярные бренды