Huawei S5700 Series Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 415

Huawei S5700 Series Скачать руководство пользователя страница 90

3

HGMP Configuration

About This Chapter

By running the Huawei Group Management Protocol (HGMP), you can appoint a switch as the
administrator switch to create a cluster and add a large number of Ethernet switches to the cluster.
The administrator is used to perform unified management and configuration over these switches,
which simplifies maintenance and engineering.

3.1 Introduction to HGMP

This part describes the reason for introducing HGMP and the typical networking of HGMP.

3.2 HGMP Features Supported by the S5700

This part describes the HGMP features supported by the S5700.

3.3 Configuring Basic HGMP Functions

This section describes how to configure basic HGMP functions to create or manage a cluster.

3.4 Configuring Advanced HGMP Functions

This section describes how to configure advanced HGMP functions to simplify the management
and maintenance of a basic cluster.

3.5 Maintaining HGMP

This section describes how to clear the statistics on NDP, and monitor the operation status of
the HGMP cluster.

3.6 HGMP Configuration Examples

This section provides several configuration examples of HGMP.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

3 HGMP Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

79

«
...
88
89
90
91
92
...
»

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов